ATS685LSHTN-T【PDF 12/15 页】IC HALL EFFECT GEAR SENSOR 4SIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录60

8页 9页 10页 11页 [12页]13页 14页 15页

Two-Wire, Zero Speed

Differential Gear Tooth Sensor IC

ATS685LSH

Allegro MicroSystems, LLC

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Undervoltage Lockout

When the supply voltage falls below the minimum operating

voltage, V

CC(UV)

, I

goes high and remains high regardless of

the state of the magnetic gradient from the target. This lockout

feature prevents false signals, caused by undervoltage conditions,

from propagating to the output of the device. Because V

below the V

(min) specification during lockout, the I

levels

may not be within specification.

Power Supply Protection

The device contains an on-chip regulator and can operate over a

wide V

range. For devices that need to operate from an unregu-

lated power supply, transient protection must be added externally.

For applications using a regulated line, EMI/RFI protection may

still be required. Contact Allegro for information on the circuitry

needed for compliance with various EMC specifications. Refer to

figure 8 for an example of a basic application circuit.

Automatic Gain Control (AGC)

This feature allows the device to operate with an optimal internal

electrical signal, regardless of the air gap (within the AG specifica-

tion). At power-on, the device determines the peak-to-peak ampli-

tude of the signal generated by the target. The gain is then auto-

matically adjusted. Figure 9 illustrates the effect of this feature.

Running Mode Gain Adjust

The ATS685 has a feature during Running mode to compensate

for dynamic air gap variation. If the system increases the mag-

netic input drastically, the device will gradually readjust the gain

downwards, allowing the chip to regain the optimum internal

electrical signal with the new, larger, magnetic signal.

Dynamic Offset Cancellation (DOC)

The offset circuitry when combined with AGC automatically

reduces the effects of chip, magnet, and installation offsets. This

circuitry is continuously active, including both Power-on mode

and Running mode, compensating for any offset drift (within

Allowable User-Induced Differential Offset). Continuous opera-

tion also allows it to compensate for offsets induced by tempera-

ture variations over time.

Running Mode Lockout

The ATS685 has a Running mode lockout feature to prevent

switching on small signals that are characteristic of vibration

signals. The internal logic of the chip evaluates small signal

amplitudes below a certain level to be vibration. In that event, the

output is blanked (locked-out) until the amplitude of the signal

returns to normal operating levels.

Watchdog

The ATS685 employs a watchdog circuit to prevent extended loss

of output switching during sudden impulses and vibration in the

system. If the system changes the magnetic input drastically such

that target feature detection is terminated, the device will fully

reset itself, allowing the chip to recalibrate properly on the new

magnetic input signal.

Mechanical Profile

Small

Large

Small

Large

Internal Differential

Analog Signal

Response, with AGC

Internal Differential

Analog Signal

Response, without AGC

Ferrous Target

V+

Figure 9. Automatic Gain Control (AGC). The AGC function corrects for

variances in the air gap. Differences in the air gap cause differences in

the magnetic field at the device, but AGC prevents that from affecting

device performance, as shown in the lowest panel.

Figure 8. Typical circuit for proper device operation.

ATS685

0.01 F (optional)

100

SENSE

LOAD

BYPASS

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式